24/7 Emergency Service Licensed & Insured · License B31188501 Financing Available Serving All of Dallas–Fort Worth
Access Control

Electric Strike vs. Magnetic Lock: Which Is Right for Your Door?

A side-by-side comparison of cost, fire code compliance and fit for commercial doors in 2026.

Access control panel wiring for a commercial door lock installation in Dallas
Real A1 project photo  Wiring behind a commercial door lock installation.

Electric strikes and magnetic locks are the two most common ways to electrify a commercial door for access control, and they work on fundamentally different principles — which affects cost, fire code compliance, and how the door behaves during a power outage. Choosing between them isn’t a style preference; it’s a decision that should be made alongside your door hardware and life-safety requirements.

On this page: How each one works · Side-by-side comparison · Fail-safe vs. fail-secure · Fire code & life-safety · Which fits which door · DFW & Allen specifics · Common mistakes · How to decide · Glossary · FAQ

How Each One Works

Quick answer: An electric strike replaces the door frame's strike plate and releases the latch electrically; a magnetic lock uses an electromagnet and armature plate to hold the door shut, with no moving parts in the lock itself.

An electric strike works with the door’s existing latch or lock, releasing it electrically to let the door open — the door can still be locked and unlocked mechanically with a key as a backup. A magnetic lock holds the door shut purely through magnetic force between an electromagnet on the frame and an armature plate on the door; removing power releases the door.

Electric Strike vs. Maglock at a Glance

FactorElectric StrikeMagnetic Lock
Typical costGenerally lowerGenerally moderate to higher
Mechanical key backupYes, works with existing lockNo, purely electromagnetic
Holding forceModerateVery high (rated in pounds of force)
Power failure behaviorConfigurable fail-safe or fail-secureAlways fail-safe (releases on power loss)
Best forStandard commercial doors with existing hardwareHigh-security doors, glass doors without a frame for a strike

Fail-Safe vs. Fail-Secure

Quick answer: Fail-safe hardware unlocks when power is lost; fail-secure hardware stays locked when power is lost. Magnetic locks are always fail-safe by design; electric strikes can be configured either way.

This distinction matters most on egress doors: fail-safe hardware is generally required so a power outage doesn’t trap people inside during an emergency. This is one reason magnetic locks on egress doors are typically paired with a required-exit device or motion sensor to ensure free exit at all times, regardless of the access control system's state.

Fire Code and Life-Safety

Quick answer: Magnetic locks on egress doors typically require a paired request-to-exit sensor or panic hardware to guarantee free exit, per fire code. This coordination is a code requirement, not optional.

Because a magnetic lock has no mechanical override, fire and life-safety codes generally require a magnetically locked egress door to also have a way to guarantee exit — commonly a request-to-exit motion sensor, a push-button release, or panic hardware. See our push bar installation page and our commercial door locks page for how these pair together. In Texas, door access hardware like this is installed by companies licensed through the Texas DPS Private Security Program, and ours holds #B31188501.

Which Fits Which Door

Standard commercial doors with existing mechanical locks are usually the best fit for an electric strike, since it works with hardware that's already there. See our electric strike installation page.

Glass storefront doors without a substantial frame, or doors requiring very high holding force, often favor a magnetic lock instead. See our magnetic lock installation page.

Doors on a required egress path need careful hardware selection either way, coordinated with fire code — this is where commercial access control planning matters most.

Door Hardware Across Dallas, Fort Worth and Allen

We install both electric strikes and magnetic locks across Dallas, Allen, Plano and Frisco, and always coordinate the choice with local fire code requirements during the project design phase.

Common Door Hardware Mistakes

  • Installing a magnetic lock on an egress door without a paired request-to-exit device, creating a code violation.
  • Choosing a magnetic lock for a door frame that could have used a lower-cost electric strike instead.
  • Not confirming fail-safe vs. fail-secure behavior matches the door's life-safety requirements.

Choosing Between a Strike and a Maglock

  1. Is this an egress door? If so, hardware and fail-safe behavior must meet fire code requirements.
  2. Does the door have a substantial frame? If not, a magnetic lock may be the more practical option.
  3. Do you need a mechanical key backup? An electric strike supports this; a magnetic lock does not.
  4. How much holding force does the door need? High-security doors often favor a magnetic lock's higher rated force.

Glossary: Door Hardware Terms

Fail-SafeHardware that unlocks when power is lost.
Fail-SecureHardware that stays locked when power is lost.
Request-to-Exit (REX)A sensor or button that signals a locked door to release for someone exiting.
Armature PlateThe metal plate on a door that a magnetic lock's electromagnet holds against.

Choosing the Right Door Hardware

We’ll evaluate your door, frame and life-safety requirements to recommend the right hardware. Call 682-516-9940 for a door-by-door recommendation, or fill out the estimate form below.

Frequently Asked Questions

Is an electric strike or magnetic lock more secure?

Magnetic locks generally offer higher rated holding force, but security also depends on correct installation and fire code coordination for either type.

Does choosing a maglock instead of a strike change the installation price?

Usually, yes. An electric strike is often the lower-cost option because it works with the door's existing latch or lock. A maglock adds the parts code expects on an exit door, such as a request-to-exit sensor and a push button, plus more wiring, so the total tends to run higher.

What does code require before a maglock goes on an exit door?

The building code typically requires a motion sensor on the egress side that releases the lock, a manual push-to-exit button near the door, and automatic release on loss of power and when the fire alarm activates. That's why many exit doors use an electric strike with panic hardware instead, since the exit device always opens the door mechanically from inside.

Can an electric strike go on a fire-rated door?

Yes, if it's a strike listed for fire doors. Those strikes must be installed fail-secure so the door stays positively latched during a fire, and people still exit through the lever or panic hardware on the inside.

Why won't my maglock door lock all the way?

The usual causes are an armature plate that's out of alignment, dirt or rust on the contact faces, a door closer that doesn't pull the door fully shut, or a request-to-exit sensor that keeps releasing the lock. Even a small gap between the magnet and the plate cuts holding force sharply.

Can an electric strike be fail-secure?

Yes, electric strikes can be configured as either fail-safe or fail-secure, unlike magnetic locks which are always fail-safe.

Can maglocks or strikes be used on double doors?

Yes, with some planning. Pairs of doors without a center mullion often use a double maglock mounted across the header. Strikes usually need a mullion to mount against, or a different approach such as electrified panic hardware.

Which strike and maglock brands do you install?

We work with HES, Securitron, Seco-Larm, Adams Rite and Ubiquiti door hardware, and choose the model by door type, frame, fire rating and how the door should behave when power is lost.

What is a request-to-exit device?

A sensor or button that detects someone approaching from inside and releases a locked door to allow exit, commonly paired with magnetic locks.

Do maglocks wear out faster than electric strikes?

Generally the opposite. A maglock has no moving parts in the lock itself, so there's little to wear. An electric strike has a moving keeper and a solenoid that wear with traffic, which is why high-use doors need a heavy-duty strike.

Call Now