24/7 Emergency Service Licensed & Insured · License B31188501 Financing Available Serving All of Dallas–Fort Worth
Electric Strike Repair

Electric Strike Repair in Dallas–Fort Worth

Door buzzes but won’t open, or the strike is stuck unlocked? We diagnose power, preload and alignment problems and repair or replace electric strikes of all brands, with 24/7 emergency service across DFW.

Electric Strike Not Working?

An electric strike replaces the fixed strike plate in the door frame with a keeper that releases when it gets power, so a button, intercom, keypad or card reader can let someone in. When it fails, you hear one of a few complaints: the door buzzes but won’t open, nothing happens at all, or the door won’t lock. A1 Security Gate & Intercom provides electric strike repair for offices, clinics, retail stores, warehouses and apartment buildings across Dallas–Fort Worth, with 24/7 emergency service for doors that are stuck locked or stuck open.

Safe Things to Check Before You Call

  • Push the door firmly closed, then try the button or card again. If it opens now, the strike is probably fighting door pressure (preload, below).
  • Listen at the frame while someone presses the button. A click or hum means power is reaching the strike; silence points to power or wiring.
  • Check whether the reader or intercom shows access granted. If it doesn’t, start with the card reader.
  • Look for a loose or bent faceplate, or a latch that hits the edge of the strike instead of dropping into it.
  • If the door won’t lock, check whether a schedule or holiday has it set to unlocked.

Please don’t tape the latch, prop the door, or disconnect anything tied to the fire alarm. Those fixes create bigger security and code problems.

Common Electric Strike Problems We Repair

Door Buzzes but Won’t Open (Preload)

This is one of the most common strike problems. The strike is getting power, but the keeper can’t swing open because the latch is pressing against it. That side pressure is called preload. It comes from tight weatherstripping, a door that has sagged, a closer pulling hard, building air pressure from the HVAC system, wind on an exterior door, or simply people pulling on the handle before the strike releases. Every strike has a preload limit, and a heavy or tightly sealed door can exceed it. The fix may be realigning the door, adjusting the seals or the latch position, or replacing the strike with one rated for more preload.

Electric strike installed in the frame of an aluminum and glass storefront door
Example: an electric strike in the frame of an aluminum storefront door. The latch has to land squarely in the keeper for the strike to release under load.

Electric Strike Not Unlocking at All (Power and Voltage)

No click and no hum usually means no power is reaching the strike. We check the power supply output, fuses, backup battery, the panel’s relay, the cable and the door cord or wiring in the frame. Voltage is another frequent culprit. Many strikes can be set for 12 or 24 volts, and a strike set to the wrong one either releases weakly or burns out. On long, thin cable runs the voltage at the door can drop far enough that the strike clicks but never fully releases. AC and DC also matter: an AC strike normally buzzes while energized, a DC strike just clicks, and a DC strike fed AC power will chatter and overheat. We measure voltage at the strike while it’s energized, which is the only reading that tells the real story.

Latch and Strike Alignment

Doors move. Hinges wear, frames shift and buildings settle, and the latch slowly drifts out of the keeper pocket. You’ll notice the door has to be pushed or lifted to latch, or the strike releases but the latch drags on the way out. On many locks the small deadlatch plunger beside the main latch must rest against the strike lip; if it drops into the keeper, the door can bind or be easy to slip open. We realign the door and strike, tighten or replace hinge hardware and adjust the faceplate so the latch lands where it should.

Strike Stuck Unlocked: Fail-Safe vs Fail-Secure Mix-Ups

A fail-secure strike stays locked without power, which suits most exterior and security doors. A fail-safe strike unlocks without power. Many strikes can be switched between the two in the field, and after a replacement or a power problem we often find one set the wrong way. That’s how a door ends up unlocked all night, or locked during an outage when it was meant to release. We also find panel outputs wired to the wrong relay contact, which flips the logic, and mechanical faults like a broken keeper spring or worn locking lever that let the keeper swing freely. Fire-rated doors must stay latched, so they use fail-secure strikes listed for fire doors; we keep that in mind on every repair.

Worn Solenoid, Chattering or Intermittent Release

A busy door can cycle its strike many times a day, and the solenoid and internal levers wear. Signs include chattering, a strike that works on the second or third try, or one that feels hot to the touch. Heat also comes from using the wrong duty rating: a strike held unlocked for hours by a business-hours schedule needs a continuous-duty rating, and an intermittent-duty strike used that way fails early.

When an Electric Strike Needs Replacement

A burned coil, a cracked body, a discontinued model or a strike that doesn’t match the lock (cylindrical, mortise and rim exit devices each need their own type) means replacement. We match the new strike to the lock, the frame prep, the voltage and the fail mode the opening needs, so it fits the existing cutout whenever possible. If you’re adding strikes to new doors, see our electric strike installation page; estimates for new installations are free.

Electric lock mounted in a stainless steel post at a pedestrian gate
Example: an electric lock in a pedestrian gate post. Gate locks fail from the same power, voltage and alignment problems as door strikes.

Electric Strike Brands We Service

We repair and replace strikes from HES, Securitron, Seco-Larm, Adams Rite, Von Duprin and Alarm Controls, along with the Altronix power supplies, card readers, intercoms and panels that run them. We repair systems installed by other companies, all brands. If the door uses a maglock or an electrified panic bar instead, see magnetic lock repair and panic bar repair. If several doors are acting up at once, the problem may be the panel or power; see access control repair.

How an Electric Strike Repair Visit Works

1

Describe the Door

Tell us what happens: buzzes but won’t open, no sound at all, or won’t lock. A photo of the strike and lock helps.

2

Diagnose on Site

Service calls start at $180 per hour. We test power and voltage at the strike, check preload and alignment, and confirm the fail mode.

3

Repair or Replace

We adjust, rewire or replace the strike and fix the power or door issue behind the failure.

4

Test and Explain

We cycle the door from every trigger, check that it latches and locks, and explain what failed.

24/7 Emergency Electric Strike Repair

A door stuck unlocked after hours, or an entrance nobody can get through in the morning, can’t wait. We offer 24/7 emergency service across DFW. Call (682) 516-9940 any time, or see our emergency service page. During regular hours we offer same-day service when the schedule allows, and you can request a repair visit online.

We repair electric strikes in Dallas, Plano, Frisco, Allen, McKinney, Richardson, Irving, Garland, Carrollton, Fort Worth and the surrounding DFW cities.

Explore More

Related Services

Local Coverage

Electric Strike Repair Across DFW

A1 repairs and replaces electric strikes for businesses and properties throughout Dallas–Fort Worth and North Texas, with 24/7 emergency service.

View All Service Areas
Answers

Frequently Asked Questions

Common questions about electric strike repair in Dallas–Fort Worth.

Why does my door buzz but not open?
The strike is getting power, but the latch is pressing on the keeper so hard it can't swing open. This is called preload, and it usually comes from tight weatherstripping, a sagging door, a strong closer or air pressure in the building. Push the door closed and try again; if it opens, the door or strike needs adjusting, or a strike rated for more preload.
Why is my electric strike not unlocking?
If you hear nothing, power isn't reaching the strike, often from a failed power supply, blown fuse, panel relay or broken wire. If it clicks but stays locked, look at low voltage at the door, a strike set to the wrong voltage, or preload. A technician measures voltage at the strike while it's energized to tell which.
Why is my electric strike stuck unlocked?
Common causes are a strike set to fail-safe where fail-secure was needed, a panel output wired to the wrong contact, an unlock schedule left on, a stuck exit button, or a broken spring inside the strike. Because the door is unsecured, this is a good reason to call our 24/7 emergency line.
Can you repair an electric strike another company installed?
Yes. We repair systems installed by other companies, all brands, including HES, Securitron, Seco-Larm, Adams Rite, Von Duprin and Alarm Controls strikes. We work with the lock, reader and power supply you already have whenever possible.
How much does an electric strike service call cost?
Service calls start at $180 per hour. The technician comes out and diagnoses the problem first. We explain the repair before doing further work. Estimates for new electric strike installations are free.
Should I repair or replace my electric strike?
Alignment, preload and power problems can usually be fixed without a new strike. A burned coil, cracked body, discontinued model or a strike that doesn't match the lock calls for replacement, and we match the new one to your lock, frame, voltage and fail mode.

Get That Door Opening Again

Call for 24/7 emergency electric strike repair anywhere in DFW. Service calls start at $180 per hour, with same-day service when the schedule allows.

Call Now